How To Jack Up A Low Car?
Well, jacking up a low car would be annoying, and sometimes you can’t fit a floor jack beneath your low-profile car. If so, you have no more to search for. We are here to guide you in this read for “How to jack up a low car.” Correspondingly, if your car is low clearance and you cannot jack it up? Hence, you should have to follow the following steps to do so.
You can also read and choose a top-rated floor jack: Best American Made Floor Jacks In 2023
How To Jack Up A Low Car? A Step-By-Step Guide
Let’s explore all these steps one by one!
How To Place A Jack Beneath A Lower Car?
If you want to lift your lowered car, you require a floor jack. As you have a low clearance car, you must have a jack with the lowest minimum height. Floor jacks are the only ones with this feature.
However, the minimum lift range ranges from 3 to 5 inches in-floor jacks. Check your car’s clearance before you get a floor jack. How low is your car? Is there a 3-inches clearance, 4 or 5 inches above the ground?
Lifting is easier if your car has one of these three ground clearances. If your car has a 2.75-inches clearance, most of the floor jacks in the market have a 2.75-inches minimum height. Therefore, you’ll require that floor jack.
Hence, you must purchase the Arcan floor jack with a 2.75-inches minimum height. Place it beneath your car. Pump the jack to lift your car.
Related Article: Are Double Locking Jack Stands Necessary?
How To Utilize Ramps For A Low Car To Raise Its Clearance?
Is there a way to get that 2.75-inches clearance? Yes, there are two ways you can raise your lower car by 2.75-inches without a jack.
The first way is more convenient, although it will cost you a few dollars, around $50. It will be terrific if you purchase a ramp for your low-profile car, possibly two ramps.
Let’s jack up your car to that 2.75-inches with these ramps. These ramps are 27.5- inches or 2.3 feet long and also 2.75-inches in height. So their loading angle is 9.05 degrees.
If your car is lower than 2.75-inches, you can quickly load your low car using these ramps. These ramps have a 9.05-degree incline angle. You’ll promptly load your car over it. And, the front of your car will not touch the ramps. As a result, you’ll get over 2.75-inches of clearance to move the floor jack beneath.
If your vehicle carries a 1.5-inches clearance, you’ll have a 4.25-inches ride height with these ramps. This clearance allows you to move the floor jack smoothly in this space. Slide it beneath and begin raising your low car.
Where Are The Major Jack Points Beneath A Low-Ground Clearance Car?
Every car has four major jack points near each wheel. Behind the doors are jack points for the front tires. Jack points for the back wheels are in front of the tires.
Some cars have one jack point between the front line wheels and the front axle to lift the front end together. A second jack point is located at the back of your car. Check the owner’s manual when you aren’t sure where the jack points are.
How To Chock A Low Car Wheels?
Before lifting your low car, the last task you require is choking the wheels. It will save you time and effort. By doing this, your car will not roll. Wheel blocking is suitable on the inclined surface.
You will probably not encounter small enough chocks to put them under your low car. When you engage the handbrake, the car will not roll up because it is down to the ground, so it won’t move or tip.
When a chock is found, you should block the opposite end. The front end must be raised, the rear wheels blocked, and the other way around.
Using A Floor Jack To Raise A Low Car
When you park your car on the concrete ground and have a jack point, raise your low car with a floor jack. So, you have to slide the jack underneath the jack point. Then begin to pump the jack. By repeatedly raising and lowering the handle, you can lift and lower your car to lift it to the desired height you need.
As far as height is concerned, raise your car heightened enough to put a jack stand beneath because jacks are used for raising purposes only, not to hold your vehicle.
Where To Locate A Jack Stand Beneath A Low Car?
Install a jack stand under once you have jack-up your car with a jack. You should install the stand next to the jack. Because you’re going to dispose of the jack, the stand will retain your car then.
Under the jack point, leave enough space for a jack stand to fit. For that, you will need to raise your car more elevated than the stand and the preferred jack stand height you want.
Once the jack stand firmly supports the car, you can change the tires or make other repairs. To make sure your vehicle is securely resting on its stands, you can shock it with your hand.
Conclusion: How To Lower A Low Car
Once you’ve finished your job, and now it’s time to lower your low car. It’s time to lower your car. Since your car is resting on the jack stand, you require hoisting your car a few inches above the jack stand. This will allow you to pull out the stand.
Put the floor jack underneath the same jack point you’ve installed before. Raise the car using the jack. When you have lifted your car high enough so that it rests on the jack, not on the jack stand, cut out the stand. Rotate the jack hold anti-clockwise to lower the jack and lower the car.
So, remove the floor jack after the car has been completely lowered. If you have employed the ramps, your car is now on them. Now you have to unload your car off the ramps. Your car has now been lowered.
I am Lucas. I am an auto enthusiast and I have many years of experience in this industry.
I created eewis.com to share my experiences and assist you to seek out the right products.
